Red Rock Threads Floriani Specials      Flat Rate US Shipping             
  Search:    
 
  Clearance And Specials Home | Contact Us | Information  
Wet N Stick  

Wet N Stick Tearaway Stabilizer

Name SizeCostQuantity
Floriani Wet N Stick Tearaway w/grid 10in X 3yd $13.95
Floriani Wet N Stick Tearaway w/grid 12in X 10yd $29.95
Floriani Wet N Stick Tearaway 12in X 10yd $31.95
Floriani Wet N Stick Tearaway w/grid 15in X 10yd $34.95
Floriani Wet N Stick Tearaway 15in X 10yd $36.95
Floriani Wet N Stick Tearaway 20in X 10yd $47.95
Floriani Wet N Stick Tearaway w/grid 20in X 10yd $49.95
Floriani Wet N Stick Tearaway W Grid Commercial Size 15in X 50yd $121.95
Floriani Wet N Stick Tearaway W Grid Commercial Size
Ships in 1-2 weeks
15in X 100yd $229.95

Floriani Wet N Stick Tearaway Stabilizer is coated with water activated, silicone based adhesive. It is an alternative to pressure sensitive sticky paper products and/or messy spray adhesives. Most home embroiderers have at some point experienced problems with peel and stick products gumming up their needles as well as the designs registration not lining up correctly. This happens because they mistake paper for stabilizer. The main differences between Wet N Stick and these products are that Floriani Wet N Stick is an embroidery stabilizer, not paper, and the adhesive doesn't get sticky residue on the needle. The adhesive on Wet N Stick can also be re-activated up to six times for easy re-positioning of garments. The unique one-inch grid lines are especially appealing for lining up cuffs and collars. Floriani Wet N Stick Tearaway Embroidery Stabilizer is also available in a black or white cut away version for times when you need to stick down a bulky stretch garment such as a sweatshirt of fleece pullover. It is important to use a cut away stabilizer on non-stable fabrics such as knit for the best embroidery results.

  • Perfect for bulky items such as towels, robes and blankets
  • Use for fabrics and garments that get "hoop burn"
  • Use for hard to hoop items such as napkin corners, collars, cuffs, etc.
  • Tears away clean from around your embroidery design
  • One layer will support around 8,000 stitches on an average size, well digitized design
  • The adhesive can be re-activated several times

To use Floriani Wet N Stick Tear Away or Cut Away:

  1. Hoop one layer of the stabilizer, adhesive side up. Be sure the product is taut within the hoop. If using Wet N Stick with a grid, line the grid marks up with the lines on your inner hoop.
  2. Apply a drop of water onto the stabilizer in each corner of the hoop as well as one in the center using a sponge, foam paint brush or envelope sealer (recommended, available at office supply stores). Remember that minimal water is required to activate the adhesive.
  3. Using the tip of your finger, smooth the drops of water over the surface of the stabilizer. You will feel the adhesive become tacky almost instantly.
  4. Press the garment into place and smooth out any wrinkles.
  5. Embroider your design. 600 stitches per minute or less is recommended.
    *Tip
    - If the design is denser than 8,000 stitches or if it is a poorly digitized design (too many stitches for designs size), float one layer of Floriani Medium Tearaway between the hoop and the bed of the machine for each additional 10,000 stitches for added support!
  6. Once the design is complete, remove the hoop from your embroidery machine and tear or cut away the Wet N Stick stabilizer. If the adhesive is holding on the garment, reactivate it by applying moisture at the glue line. Once the adhesive is re-activated it will release the garment.
Floriani Bonuses
Tearaways
Cutaways
Water Solubles
Specialty
Batting
Kits & Samples
 
Customer Service
Fabshopnet
Orders may be placed online
or by phone, fax, or mail
Red Rock Threads is an internet shop only
Questions? Contact us
Red Rock Threads, Inc
2160 E Calvada Blvd
Suite #C
Pahrump, NV 89048